Varnishes & Fixatives

• 100% acrylic polymer varnish
• Water soluble when wet
• Good chemical and water resistance when dry
• Non-tacky
• Hard, yet flexible surface
• Resistant to dirt retention
• Resists discolouring due to humidity, heat and ultraviolet light (non-yellowing, non-fogging)
• Depending upon substrate, allows moisture to pass through (breathable)
• Not for use over oil paint
• Protects acrylic colour
• Archival
• For interior and exterior use

• Apply as a final varnish over dry acrylic paint.
• Varnish surface and environment must be clean, dry and dust free.
• Acrylic paintings must be completely dried and cured for 48-72 hours before varnishing. Thicker acrylic applications may take more time to cure.
• Application may be done by brush or spray. Generally a sprayed application will be thinner, smoother and more even. Rolling or sponging application is not recommended.

• Use a wide, soft hair brush. Generally, a 1 to 4 inch flat brush is used, depending on the surface area.
• Apply Liquitex varnish in 1-3 thin coats, rather than 1 thick coat. A thick coat will take longer to dry, may dry cloudy, may drip or sag during application and has a greater chance of showing brush strokes when dry.
• When applying Liquitex Matte Varnish, apply no more than 1-2 thin coats. A thick application may result in cloudiness when dry. If more than 2 coats are desired, first varnish with gloss varnish until desired thickness is achieved and then apply a final coat of matte varnish.
• Canvas should be placed horizontally in order to prevent the varnish from running. After varnishing, the surface should be shielded with a protective "tent". This will prevent any dust or airborne particles from settling into varnish as it dries.
• Apply Liquitex varnish in slightly overlapping pattern that covers entire artwork. Apply in horizontal and vertical brush strokes, so that entire area is evenly coated.
• Do not rework areas you might miss as the brush could pick up partially dried varnish and cause clouding. If areas are missed, wait until the varnish is dry and apply another coat.

Liquitex Soluvar Varnish can be applied to acrylic or oil canvases. It dries into a clear, solid and non-sticky film that is resistant to water, dust and discoloration. This varnish evens out automatically and does not allow paintbrush marks to show. It offers both a permanent and temporary surface, which protects the canvas and allows for easy removal of dust and stains.

Glossy Soluvar Varnish enhances the depth and intensity of colours, while Matte Soluvar Varnish reduces their intensity, depth and shine.

MSA (Mineral Spirit Acrylic) Varnish with UVLS (Ultraviolet Light Stabilisers) is a mineral spirit-based acrylic resin system that forms a tougher, less permeable film than water­borne acrylic varnishes. It can be applied to acrylic, oil and alkyd painted surfaces. It reduces dirt penetration and surface marring, offering an ex­treme­ly level film with less foam and fewer pin­holes. It is removable with mineral spirits after drying and is recommended for interior or exterior use.

• 100% acrylic polymer varnish
• Water soluble when wet
• Good chemical and water resistance when dry
• Non-tacky
• Hard, yet flexible surface
• Resistant to dirt retention
• Resists discolouring due to humidity, heat and ultraviolet light (non-yellowing, non-fogging)
• Depending upon substrate, allows moisture to pass through (breathable)
• Not for use over oil paint
• Protects acrylic colour
• Archival
• For interior and exterior use

• Apply as a final varnish over dry acrylic paint.
• Varnish surface and environment must be clean, dry and dust free.
• Acrylic paintings must be completely dried and cured for 48-72 hours before varnishing. Thicker acrylic applications may take more time to cure.
• Application may be done by brush or spray. Generally a sprayed application will be thinner, smoother and more even. Rolling or sponging application is not recommended.

• Use a wide, soft hair brush. Generally, a 1 to 4 inch flat brush is used, depending on the surface area.
• Apply Liquitex varnish in 1-3 thin coats, rather than 1 thick coat. A thick coat will take longer to dry, may dry cloudy, may drip or sag during application and has a greater chance of showing brush strokes when dry.
• When applying Liquitex Matte Varnish, apply no more than 1-2 thin coats. A thick application may result in cloudiness when dry. If more than 2 coats are desired, first varnish with gloss varnish until desired thickness is achieved and then apply a final coat of matte varnish.
• Canvas should be placed horizontally in order to prevent the varnish from running. After varnishing, the surface should be shielded with a protective "tent". This will prevent any dust or airborne particles from settling into varnish as it dries.
• Apply Liquitex varnish in slightly overlapping pattern that covers entire artwork. Apply in horizontal and vertical brush strokes, so that entire area is evenly coated.
• Do not rework areas you might miss as the brush could pick up partially dried varnish and cause clouding. If areas are missed, wait until the varnish is dry and apply another coat.

Clear, non-yellowing synthetic resin and alcohol fixative. Designed for pencil and charcoal, this fixative creates a resistant, protecting film. Due to its high resin content, use with soft pastels is not recommended. To use, spray the surface lightly, building up successive protective layers if necessary.

Quantity: 13.50 oz (400 ml)

• non-yellowing
• painting must be completely dry (6-12 months)
• use only as a final varnish
• shake well before use

• Pop Art Study Acrylic
• Fine Studio Acrylics
• Studio Acrylics Auxiliaries
• Artist Extra Fine Acrylics
• Matte Pub
• Mass Market (Acrylic)
• Mixed Media
• decoCream

• interior and exterior use
• 100% acrylic polymer varnish
• adjusts and unifies surface sheen
• protects and resists dirt retention
• increases brightness and colour saturation
• resists discolouration
• semi-opaque when wet
• transparent when dry

• 100% acrylic polymer varnish
• Water soluble when wet
• Good chemical and water resistance when dry
• Non-tacky
• Hard, yet flexible surface
• Resistant to dirt retention
• Resists discolouring due to humidity, heat and ultraviolet light (non-yellowing, non-fogging)
• Depending upon substrate, allows moisture to pass through (breathable)
• Not for use over oil paint
• Protects acrylic colour
• Archival
• For interior and exterior use

• Apply as a final varnish over dry acrylic paint.
• Varnish surface and environment must be clean, dry and dust free.
• Acrylic paintings must be completely dried and cured for 48-72 hours before varnishing. Thicker acrylic applications may take more time to cure.
• Application may be done by brush or spray. Generally a sprayed application will be thinner, smoother and more even. Rolling or sponging application is not recommended.

• Use a wide, soft hair brush. Generally, a 1 to 4 inch flat brush is used, depending on the surface area.
• Apply Liquitex varnish in 1-3 thin coats, rather than 1 thick coat. A thick coat will take longer to dry, may dry cloudy, may drip or sag during application and has a greater chance of showing brush strokes when dry.
• When applying Liquitex Matte Varnish, apply no more than 1-2 thin coats. A thick application may result in cloudiness when dry. If more than 2 coats are desired, first varnish with gloss varnish until desired thickness is achieved and then apply a final coat of matte varnish.
• Canvas should be placed horizontally in order to prevent the varnish from running. After varnishing, the surface should be shielded with a protective "tent". This will prevent any dust or airborne particles from settling into varnish as it dries.
• Apply Liquitex varnish in slightly overlapping pattern that covers entire artwork. Apply in horizontal and vertical brush strokes, so that entire area is evenly coated.
• Do not rework areas you might miss as the brush could pick up partially dried varnish and cause clouding. If areas are missed, wait until the varnish is dry and apply another coat.

• 100% acrylic polymer varnish
• Water soluble when wet
• Good chemical and water resistance when dry
• Non-tacky
• Hard, yet flexible surface
• Resistant to dirt retention
• Resists discolouring due to humidity, heat and ultraviolet light (non-yellowing, non-fogging)
• Depending upon substrate, allows moisture to pass through (breathable)
• Not for use over oil paint
• Protects acrylic colour
• Archival
• For interior and exterior use

• Apply as a final varnish over dry acrylic paint.
• Varnish surface and environment must be clean, dry and dust free.
• Acrylic paintings must be completely dried and cured for 48-72 hours before varnishing. Thicker acrylic applications may take more time to cure.
• Application may be done by brush or spray. Generally a sprayed application will be thinner, smoother and more even. Rolling or sponging application is not recommended.

• Use a wide, soft hair brush. Generally, a 1 to 4 inch flat brush is used, depending on the surface area.
• Apply Liquitex varnish in 1-3 thin coats, rather than 1 thick coat. A thick coat will take longer to dry, may dry cloudy, may drip or sag during application and has a greater chance of showing brush strokes when dry.
• When applying Liquitex Matte Varnish, apply no more than 1-2 thin coats. A thick application may result in cloudiness when dry. If more than 2 coats are desired, first varnish with gloss varnish until desired thickness is achieved and then apply a final coat of matte varnish.
• Canvas should be placed horizontally in order to prevent the varnish from running. After varnishing, the surface should be shielded with a protective "tent". This will prevent any dust or airborne particles from settling into varnish as it dries.
• Apply Liquitex varnish in slightly overlapping pattern that covers entire artwork. Apply in horizontal and vertical brush strokes, so that entire area is evenly coated.
• Do not rework areas you might miss as the brush could pick up partially dried varnish and cause clouding. If areas are missed, wait until the varnish is dry and apply another coat.

This Krylon spray protects work from humidity. Fingerprints, and prevents discolouration. It is permanent, does not yellow and dries quickly. For use on pencil, charcoal or ink drawings, watercolour paintings and photographs.

Made from protective acrylic resin, this Sennelier fixative is perfect for artists seeking a powerful fixative which will not alter the appearance of their work. For an accurate application with minimal excess spray, turn the yellow nozzle in the cap to achieve the desired spray pattern, either horizontal or vertical.

Characteristics:

• Lightfast
• Permanent
• Water resistant
• Does not yellow

Suitable for: pastels, charcoal, watercolour, ink, acrylic, gilding, photos, block-out/surface preparation.

Surfaces: paper, canvas, wood, glass, ceramic, porcelain, walls.

Quantity: 13.50 oz (400 ml)

Adds durability to wood furniture, protecting against water and stains. For use with wood, metal, wicker, glass, plaster, ceramic, papier mache and more.

• Clear finish available in gloss and satin
• Dura-Shield protection
• Ideal for furniture, countertops, cabinets and more
• Fast dry
• Dries to the touch within 15 minutes

MSA (Mineral Spirit Acrylic) Varnish with UVLS (Ultraviolet Light Stabilisers) is a mineral spirit-based acrylic resin system that forms a tougher, less permeable film than water­borne acrylic varnishes. It can be applied to acrylic, oil and alkyd painted surfaces. It reduces dirt penetration and surface marring, offering an ex­treme­ly level film with less foam and fewer pin­holes. It is removable with mineral spirits after drying and is recommended for interior or exterior use.

• Permanent, protective matte finish
• Non-yellowing
• Moisture-resistant
• Dries to the touch in 10 minutes
• Dries sufficiently for handling within 3 hours
   

• Do not use until painting is completely dry (6-12 months)
• Use in warm, dry conditions
• Do not use as a medium

• Pop Art Study Acrylic
• Fine Studio Acrylics
• Studio Acrylics Auxiliaries
• Artist Extra Fine Acrylics
• Matte Pub
• Mass Market (Acrylic)
• Mixed Media
• decoCream